FX60 ERW Tube Mill for Φ25-89 mm Steel Tube Production
FX60 is positioned for medium structural tube projects where larger sections, higher wall thicknesses and a wider square-tube range make line strength, strip preparation and material handling more important. It is aimed at a different buyer decision than FX45: not just more sizes, but a heavier production program.
Round Tube Reference
Φ25-89 mm / 0.8-3.5 mm
Square Tube Reference
20×20-70×70 mm / 0.8-3.0 mm
Best-Fit Production Direction
medium structural tube and thicker-wall hollow-section production
Engineering confirmation required: published model values are preliminary references. Final capability, configuration and production conditions follow the approved technical agreement.
Suitable Orders for FX60
- medium structural round tube for construction and fabrication
- square and rectangular hollow sections for frames and supports
- machinery base, rack and industrial fabrication tube
- larger fence, gate and general building-material products
Selection Boundary
The project should be checked against coil specification, welding demand, cutting method and workshop flow. If the product list is concentrated below the FX60 range, FX45 may be more efficient; if it regularly approaches larger structural sections, compare FX76 before civil and layout planning.
FX60 project planning should include a simple material-flow drawing from coil storage to finished-tube packing. This exposes whether the factory has enough line length, crane access, operator space and downstream handling for medium structural products before equipment configuration is finalized.
FX60 Selection Profile: Medium Structural and Thicker Wall
FX60 is appropriate when the business plan contains enough medium structural volume to justify stronger forming, welding, cutting and handling. It should not be chosen only as future insurance.
Best Product Mix
Medium round and hollow sections with recurring structural applications, meaningful thicker-wall demand and a clear plan for square or rectangular output.
Critical Engineering Point
Heavier strip changes coil handling, entry, drive, welding, cooling, cutting and finished-tube flow. Confirm coil data and workshop crane conditions early.
Choose FX76 Instead When
Compare FX76 when the order portfolio regularly requires larger sections or when products near the FX60 upper limit would dominate production rather than occur occasionally.
When FX60 Is a Strong Fit
FX60 is most practical when recurring orders genuinely use its medium structural tube and thicker-wall hollow-section production direction. The dominant products should fit the published reference without forcing the line to spend most of its time at an unsuitable boundary.
When to Compare Another Model
Compare FX45 when most orders sit below this range. Compare FX76 when larger or heavier products are recurring commercial requirements rather than occasional possibilities.
Main Configuration Priorities
- Coil handling and strip preparation reviewed for wider, heavier material
- Mill stand, shaft and drive discussion focused on structural product demand
- HF welding and cooling selected from the upper working combinations
- Sizing and square-forming plan based on the confirmed hollow-section portfolio
- Cutting, run-out and packing designed for heavier finished tube handling
Production Process and Engineering Focus
Entry and Strip Preparation
Uncoiler capacity and coil handling are reviewed around the wider strip and heavier material used by medium sections. Leveling and entry guidance must control strip position before the increased forming load enters the mill.
Accumulation and Forming
The accumulator and strip-joining plan are matched to workshop length and the intended operating rhythm. Forming design considers structural material, wall distribution and the main round-to-square product route.
Welding, Cooling and Sizing
HF welding and squeeze-roll setup are reviewed for the demanding size-and-wall combinations in the order mix. Cooling and sizing control heat, geometry and dimensional consistency before final hollow-section shaping.
Cutting and Finished-Tube Handling
The cutting system is selected for the confirmed wall, length and end-quality requirements of heavier tube. Run-out and packing equipment should reduce manual handling risk as finished section size and weight increase.
Information Needed for a FX60 Review
Product Matrix
- Every tube size and matching wall thickness
- Round, square and rectangular shapes
- Material grade and surface condition
- Finished length and cutting requirements
Factory and Project Inputs
- Recurring order priorities and future sizes
- Coil specification and strip preparation
- Voltage, workshop layout and lifting conditions
- Installation, training and spare-parts expectations
FX60 Tube Mill FAQ
Is FX60 only a larger version of FX45?
No. The larger published reference range can require different decisions for coil handling, forming load, welding, cooling, cutting and finished-tube movement. The whole production flow should be reviewed.
What information matters most for an FX60 quotation?
Provide the size-by-thickness list, material grades, main monthly products, square and rectangular sections, finished length, coil data, voltage and workshop layout.
When should FX60 be compared with FX76?
Compare them when the main order portfolio approaches the FX60 upper range or when heavier structural products are expected regularly. Occasional future possibilities alone do not justify the larger model.
Request Your Tube Mill Solution
Send the complete size-by-thickness list for a FX60 engineering review. XFX will compare adjacent models when the order mix sits near the published reference boundary.